Close



Dig deeper, search our News website




Search:

Type: Posts; User: Danno

Search: Search took 0.00 seconds.

  1. Replies
    25
    Views
    125,542

    Sticky: 32 bit version? Do tell!

    Hey curious aardvark,
    Do you still have a32 bit version of the Maker ware software? I'd love to get my hands on that if you do.

    Thanks Dan
  2. Replies
    25
    Views
    125,542

    Sticky: Hello Geoff, Do you happen to know where I...

    Hello Geoff,

    Do you happen to know where I can get a 32bit version of Makerware?
    I do have the 64bit version on my work laptop but I thought it would be good to have software on a dedicated...
  3. Replies
    19
    Views
    17,725

    Yeah I tried a PLA raft and couldn't get the PVA...

    Yeah I tried a PLA raft and couldn't get the PVA to stick to it.
    Gonna try a very low print speed and see if that works.
  4. Replies
    19
    Views
    17,725

    What speeds and temps did you use? I have tried...

    What speeds and temps did you use? I have tried ABS and PLA and nothing seems to stick to the PVA.

    Just occurred to me that I could try a slow speed. All attempts so far have been at 40.

    Dan
  5. I intend to figure this out with Slic3r since it...

    I intend to figure this out with Slic3r since it gives me use of both extruders even on single color prints. I intend to use the second extruder for support material such as HIPS or PVA (soluble...
  6. Cool. I've found that in the GPX code which...

    Cool.

    I've found that in the GPX code which creates the x3g file has some settings that tell it to ignore the gcode settings.
    I think they are for some printers that need to operate...
  7. NOTE: I have tracked this down to an issue...

    NOTE: I have tracked this down to an issue between Slic3r's gcode generation and the gpx scripted x3g file creation.

    the gcode shows the correct settings, but somehow when its creating the x3g...
  8. Yes John, I followed that instruction twice...

    Yes John,

    I followed that instruction twice to make sure I didn't miss any settings.
    I am new to the ol 3d printing world so the gcode is still new to me as well. I'm learning at a fast pace...
  9. Print Bed not heating up when using Slic3r files

    I am trying to use Slic3r files on my FlashForge Creator Pro but when I do, it doesn't heat the print bed.
    The config is set for 2 extruders, but I cannot find the printbead heat settings anywhere....
  10. Thread: PVA Settings?

    by Danno
    Replies
    4
    Views
    8,651

    I was using ReplicatorG and it doesn't have...

    I was using ReplicatorG and it doesn't have separate extruder settings unless you're doing a dual printer file.
    I installed MakerWare and had some luck getting it to use the left extruder (2) as...
  11. Replies
    19
    Views
    17,725

    Yeah I am having the exact same results. PVA...

    Yeah I am having the exact same results. PVA sticks nicely to the bed but the ABS refuses to adhere to the PVA. I've tried temps from 190 to 230 on the PVA and no change.

    I've seen mixed...
  12. Replies
    25
    Views
    125,542

    Sticky: Awesome, been looking for this. Thanks Geoff ...

    Awesome, been looking for this.
    Thanks Geoff

    Look at that, joined the forum and within minutes its paying off.!
  13. Thread: PVA Settings?

    by Danno
    Replies
    4
    Views
    8,651

    jfkansas, How do you set the FF Creator Pro to...

    jfkansas, How do you set the FF Creator Pro to use one extruder to be used as support material and other as the main print?
    Just got the printer a few weeks ago and have a spool of PVA but have yet...
  14. Replies
    19
    Views
    17,725

    Also curious about PVA. Plan to give it a try...

    Also curious about PVA.
    Plan to give it a try but thought I'd check the forum first.
    Looks like I'm not the only one. :)
Results 1 to 14 of 14