Search:

Well I installed a Flexion extruder this past weekend, along with the HT upgraded mounting bar/headbreak, and one HT hotend (This is because the stock QiDi hotend barrels are too small to fit...

Do you have a link to this??

Do you have a link to this?

I have a question for all the QIDI Guru's out there, (Yous guys)

I have found that I need to replace my extruder motors, and they are as follows:

42HB34F08AB rated at .8 amps.

I have found...

Oh yeah they run really fast when loading for sure lol.

Yes I am looking to replace a extruder motor. And looking for something cheap and closer than China lol.

So as far you think I am good to...

any chance someone here more knowledgable about stepper motors can answer my question in the last page? :D

Has anyone relaxed a stepper motor yet on these? Looking for a cheaper (and more local) option.

Do do you think these would work?

LEORX Nema 17 2 Phase 4-Wire 1.5A 40mm 1.8° Stepper Motor for...

What is the final (Latest) word for All Metal Hotends from Micro Swiss on the printer?

How many people have one or two installed? What do you think of it?

Looking to see if it is worth it. I...

I wish there was a nicer way to level the entire carriage. Someone should make a carriage that has thumb screws to adjust the height up and down.

What about if we switch out to the all metal hotend of the Swiss style? lola

And I meant the Quickly release and move the hot end up and down part.

Hopefully you can get it to work with the...

I have been interested on the upgrade you have on your site but I am not sure how it all goes together, and how the quick release is used, etc. And you haven't added a working link for the...

I print NinjaFlex all the time with my QIDI printer. Just print out the FFCP upgraded extruder and you will be good to go!

The way I manage lowering temp is with the temperature tab. I select the starting layer i want it to start cooling off then lower it a couple degrees and add it, then do the next layer, etc etc etc....

'Pull off' as in remove :) I rarely have to touch anything as I said the cooling and the plate quickly (shrinkage) and then flexing and the parts fall off. And I print about half and half ABS and...

That's just it, I don't have to touch the parts lol. Just the fact of the sheet cooling so quickly loosens most of the parts, then a gentle flex of the plate and they fall off. :D

Also I have...

I have absolutely NO problems with BuildTak. I have even used it to print ABS on my Fabrikator Mini without a heated bed. I have used Glass in the past, and still prefer my flexible plate with...

Even if it does deform at some point (I have printed hundreds of things and they are all still perfectly flat) the magnets are spread across the entire plate and hold it down quite well. Also...

With the Maghold system you have a solid aluminum block with magnets in it, then you have flexible spring steel sheets with kapton tape on one side and BuildTak on the other that attach magnetically...

They have great support and should have no problem replacing the part. I got a badly cut spring steel sheet that didn't quite fit right and they sent me another one along with a free buildtak sheet.

I have this EXACT same issue on mine. It actually got really really loud on prints that ran multiple hours. They sent me some steps to try of loosening the grub screws on the back left and right...

Sometimes the settings from the panel confuse me...

I think my acceleration is 'off' as when I go to the settings page it reads 'Acceleration ON' and I think that means clicking on it will turn it...

The 'Buy it now' ones all have a box for 'make an offer'. Make and offer of $680 now (Used to work at $630 lol) and they will accept it :D

Lol. I use S3D already.

I I have been printing at whatever their default speed is.

Question about minimizing shaking of the bed.

I I was noticing that the bed would shake and vibrate when the printer would get to doing infill and I read that causes the band in and shodows and...

So I think I figured out what the second music is.

I was watching it print this afternoon and realized that the music played at every layer I had scheduled for a temperature change! So it is when...