Close



Page 53 of 55 FirstFirst ... 3435152535455 LastLast
Threads 1041 to 1060 of 1098

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 04:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 48,042
    08-12-2016, 11:26 AM Go to last post
    • Replies: 1
    • Views: 959
    04-13-2014, 06:56 AM Go to last post
    • Replies: 3
    • Views: 14,137
    04-12-2014, 09:32 AM Go to last post
  1. DCM for Smoothing PLA prints - WTF is DCM?

    Started by The_Critter, 04-11-2014 01:19 PM
    • Replies: 5
    • Views: 2,316
    04-11-2014, 06:11 PM Go to last post
    • Replies: 4
    • Views: 1,476
    04-09-2014, 05:38 PM Go to last post
    • Replies: 3
    • Views: 1,546
    04-07-2014, 04:53 PM Go to last post
  2. How to Calibrate a 3D Printer Extruder

    Started by EveryDayIDream, 04-06-2014 07:26 AM
    • Replies: 1
    • Views: 2,249
    04-06-2014, 10:39 AM Go to last post
  3. 3D printer prints warped objects

    Started by BikeRide, 03-30-2014 01:37 PM
    • Replies: 3
    • Views: 1,023
    04-01-2014, 07:11 AM Go to last post
  4. What could be causing these problems?

    Started by Ka50, 03-23-2014 10:28 AM
    • Replies: 7
    • Views: 2,142
    03-30-2014, 05:08 PM Go to last post
  5. Pronterface install problem

    Started by old man emu, 03-27-2014 02:45 AM
    • Replies: 4
    • Views: 5,839
    03-30-2014, 08:28 AM Go to last post
  6. Getting down and dirty with Slic3r

    Started by old man emu, 03-26-2014 02:09 AM
    • Replies: 1
    • Views: 973
    03-28-2014, 07:29 AM Go to last post
  7. Question Printing with Wood Filament & Final Finishes

    Started by jssnoopy, 03-25-2014 11:51 PM
    • Replies: 6
    • Views: 1,578
    03-27-2014, 01:48 PM Go to last post
  8. Hot end Prusia i3

    Started by Creted3d, 03-17-2014 06:34 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 5,060
    03-26-2014, 08:31 PM Go to last post
  9. How to set up endstop switches.

    Started by old man emu, 03-13-2014 07:04 AM
    • Replies: 3
    • Views: 1,386
    03-26-2014, 06:30 PM Go to last post
  10. Reducing materials used during a 3D print

    Started by squadus, 03-19-2014 03:46 PM
    • Replies: 2
    • Views: 883
    03-26-2014, 06:21 PM Go to last post
  11. Measuring RAMPS Board Stepper Motor Voltage

    Started by old man emu, 03-24-2014 08:19 PM
    • Replies: 2
    • Views: 3,310
    03-25-2014, 07:07 PM Go to last post
  12. Possible to print with no lines with FDM

    Started by pathfindr, 03-23-2014 10:15 AM
    • Replies: 2
    • Views: 958
    03-24-2014, 07:56 AM Go to last post
    • Replies: 5
    • Views: 1,089
    03-23-2014, 10:49 AM Go to last post
  13. Need some Firmware help

    Started by Vonnely, 03-20-2014 02:38 PM
    • Replies: 3
    • Views: 1,051
    03-21-2014, 06:28 PM Go to last post
  14. Best "Statue Looking" Filament?

    Started by QuitNoMore, 03-17-2014 03:27 PM
    • Replies: 1
    • Views: 1,400
    03-21-2014, 06:36 AM Go to last post

Page 53 of 55 FirstFirst ... 3435152535455 LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •