Close


Flash Forge Inventor




Page 51 of 54 FirstFirst ... 414950515253 ... LastLast
Threads 1001 to 1020 of 1061

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 04:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 44,597
    08-12-2016, 11:26 AM Go to last post
  1. Question Print Goes Askew Around the 4th Layer

    Started by Wayneman, 04-07-2014 03:29 PM
    askew, out of alignment
    • Replies: 4
    • Views: 1,481
    04-17-2014, 04:36 PM Go to last post
  2. Bigger Printers - Bigger Printbeds

    Started by old man emu, 04-13-2014 04:32 PM
    • Replies: 3
    • Views: 1,212
    04-15-2014, 05:34 PM Go to last post
    • Replies: 0
    • Views: 608
    04-13-2014, 11:04 AM Go to last post
    • Replies: 1
    • Views: 924
    04-13-2014, 06:56 AM Go to last post
    • Replies: 3
    • Views: 13,101
    04-12-2014, 09:32 AM Go to last post
  3. DCM for Smoothing PLA prints - WTF is DCM?

    Started by The_Critter, 04-11-2014 01:19 PM
    • Replies: 5
    • Views: 2,113
    04-11-2014, 06:11 PM Go to last post
    • Replies: 4
    • Views: 1,415
    04-09-2014, 05:38 PM Go to last post
    • Replies: 3
    • Views: 1,465
    04-07-2014, 04:53 PM Go to last post
  4. How to Calibrate a 3D Printer Extruder

    Started by EveryDayIDream, 04-06-2014 07:26 AM
    • Replies: 1
    • Views: 1,948
    04-06-2014, 10:39 AM Go to last post
  5. 3D printer prints warped objects

    Started by BikeRide, 03-30-2014 01:37 PM
    • Replies: 3
    • Views: 950
    04-01-2014, 07:11 AM Go to last post
  6. What could be causing these problems?

    Started by Ka50, 03-23-2014 10:28 AM
    • Replies: 7
    • Views: 2,028
    03-30-2014, 05:08 PM Go to last post
  7. Pronterface install problem

    Started by old man emu, 03-27-2014 02:45 AM
    • Replies: 4
    • Views: 5,318
    03-30-2014, 08:28 AM Go to last post
  8. Getting down and dirty with Slic3r

    Started by old man emu, 03-26-2014 02:09 AM
    • Replies: 1
    • Views: 911
    03-28-2014, 07:29 AM Go to last post
  9. Question Printing with Wood Filament & Final Finishes

    Started by jssnoopy, 03-25-2014 11:51 PM
    • Replies: 6
    • Views: 1,498
    03-27-2014, 01:48 PM Go to last post
  10. Hot end Prusia i3

    Started by Creted3d, 03-17-2014 06:34 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 4,820
    03-26-2014, 08:31 PM Go to last post
  11. How to set up endstop switches.

    Started by old man emu, 03-13-2014 07:04 AM
    • Replies: 3
    • Views: 1,312
    03-26-2014, 06:30 PM Go to last post
  12. Reducing materials used during a 3D print

    Started by squadus, 03-19-2014 03:46 PM
    • Replies: 2
    • Views: 838
    03-26-2014, 06:21 PM Go to last post
  13. Measuring RAMPS Board Stepper Motor Voltage

    Started by old man emu, 03-24-2014 08:19 PM
    • Replies: 2
    • Views: 3,072
    03-25-2014, 07:07 PM Go to last post
  14. Possible to print with no lines with FDM

    Started by pathfindr, 03-23-2014 10:15 AM
    • Replies: 2
    • Views: 907
    03-24-2014, 07:56 AM Go to last post

Page 51 of 54 FirstFirst ... 414950515253 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •