Close



Page 48 of 51 FirstFirst ... 384647484950 ... LastLast
Threads 941 to 960 of 1004

Forum: Tips, Tricks and Tech Help

Tips & Tricks to tweak your printers, as well as technical help. Topics MUST contain the type of printer you are addressing!

  1. Sticky Thread Sticky: OpenScad Help Centre

    Started by old man emu, 11-28-2014 04:15 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 38,042
    08-12-2016, 11:26 AM Go to last post
  1. Need to grind your plastic down for an exruder?

    Started by RobH2, 04-02-2014 11:00 AM
    extruder, nitrogen, pellets, scrap, shredder
    • Replies: 8
    • Views: 2,068
    04-19-2014, 02:25 PM Go to last post
  2. Printer Lubrication - How Often?

    Started by Mr.Abrams, 04-17-2014 07:50 AM
    • Replies: 4
    • Views: 1,607
    04-19-2014, 12:16 PM Go to last post
  3. Bonding PLA and ABS - Is it possible?

    Started by KrypTONight, 04-14-2014 04:39 PM
    • Replies: 1
    • Views: 862
    04-19-2014, 09:10 AM Go to last post
  4. Question Print Goes Askew Around the 4th Layer

    Started by Wayneman, 04-07-2014 03:29 PM
    askew, out of alignment
    • Replies: 4
    • Views: 1,315
    04-17-2014, 04:36 PM Go to last post
  5. Bigger Printers - Bigger Printbeds

    Started by old man emu, 04-13-2014 04:32 PM
    • Replies: 3
    • Views: 1,098
    04-15-2014, 05:34 PM Go to last post
    • Replies: 0
    • Views: 557
    04-13-2014, 11:04 AM Go to last post
    • Replies: 1
    • Views: 840
    04-13-2014, 06:56 AM Go to last post
    • Replies: 3
    • Views: 11,136
    04-12-2014, 09:32 AM Go to last post
  6. DCM for Smoothing PLA prints - WTF is DCM?

    Started by The_Critter, 04-11-2014 01:19 PM
    • Replies: 5
    • Views: 1,736
    04-11-2014, 06:11 PM Go to last post
    • Replies: 4
    • Views: 1,309
    04-09-2014, 05:38 PM Go to last post
    • Replies: 3
    • Views: 1,248
    04-07-2014, 04:53 PM Go to last post
  7. How to Calibrate a 3D Printer Extruder

    Started by EveryDayIDream, 04-06-2014 07:26 AM
    • Replies: 1
    • Views: 1,502
    04-06-2014, 10:39 AM Go to last post
  8. 3D printer prints warped objects

    Started by BikeRide, 03-30-2014 01:37 PM
    • Replies: 3
    • Views: 818
    04-01-2014, 07:11 AM Go to last post
  9. What could be causing these problems?

    Started by Ka50, 03-23-2014 10:28 AM
    • Replies: 7
    • Views: 1,842
    03-30-2014, 05:08 PM Go to last post
  10. Pronterface install problem

    Started by old man emu, 03-27-2014 02:45 AM
    • Replies: 4
    • Views: 4,412
    03-30-2014, 08:28 AM Go to last post
  11. Getting down and dirty with Slic3r

    Started by old man emu, 03-26-2014 02:09 AM
    • Replies: 1
    • Views: 732
    03-28-2014, 07:29 AM Go to last post
  12. Question Printing with Wood Filament & Final Finishes

    Started by jssnoopy, 03-25-2014 11:51 PM
    • Replies: 6
    • Views: 1,366
    03-27-2014, 01:48 PM Go to last post
  13. Hot end Prusia i3

    Started by Creted3d, 03-17-2014 06:34 AM
    3 Pages
    1 2 3
    • Replies: 22
    • Views: 4,385
    03-26-2014, 08:31 PM Go to last post
  14. How to set up endstop switches.

    Started by old man emu, 03-13-2014 07:04 AM
    • Replies: 3
    • Views: 1,204
    03-26-2014, 06:30 PM Go to last post

Page 48 of 51 FirstFirst ... 384647484950 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •