Close



Page 3 of 6 FirstFirst 12345 ... LastLast
Threads 41 to 60 of 111

Forum: CTC 3D Printers

Discussion related to CTC Duplicator/Bizer Printers

  1. Sticky Thread Sticky: Sailfish Manual - Setting up your printer - READ THIS

    Started by Sebastian Finke, 12-18-2015 02:29 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 9,892
    01-01-2016, 07:54 AM Go to last post
  1. Question Need new MightBoard (suggestion)

    Started by TiredJuan, 03-12-2016 01:11 PM
    2 Pages
    1 2
    • Replies: 10
    • Views: 2,895
    05-09-2016, 08:55 PM Go to last post
  2. Unhappy CTC printer problems

    Started by ICC, 05-04-2016 02:44 PM
    • Replies: 7
    • Views: 1,647
    05-08-2016, 04:37 PM Go to last post
  3. Yet Another CTC Newbie - 2 1/2 questions.

    Started by adrianq, 04-29-2016 05:57 PM
    • Replies: 2
    • Views: 1,028
    05-04-2016, 02:25 PM Go to last post
  4. New CTC 3D owner

    Started by noiseboy72, 04-27-2016 04:49 PM
    • Replies: 5
    • Views: 1,218
    04-29-2016, 01:41 PM Go to last post
  5. Slic3r optimal gcode for CTC printet

    Started by tintalala, 04-27-2016 06:04 AM
    • Replies: 1
    • Views: 1,461
    04-28-2016, 09:02 PM Go to last post
  6. 20mm x 20mm test square is slighty off square

    Started by Raymo, 04-24-2016 12:20 PM
    • Replies: 4
    • Views: 1,098
    04-27-2016, 04:42 PM Go to last post
  7. Switched to Sailfish, but head is printing off the bed, not in middle.

    Started by Raymo, 04-10-2016 10:00 AM
    3 Pages
    1 2 3
    • Replies: 20
    • Views: 4,138
    04-18-2016, 05:40 AM Go to last post
  8. I just bought a CTC too..

    Started by Geoff, 03-10-2016 02:12 AM
    • Replies: 9
    • Views: 2,289
    04-11-2016, 05:33 PM Go to last post
    • Replies: 9
    • Views: 2,007
    04-10-2016, 09:48 AM Go to last post
  9. Bed temperature reading low - ABS lifting

    Started by d43d, 02-15-2016 12:47 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 3,416
    04-09-2016, 03:28 PM Go to last post
  10. ctc extruder wiring help

    Started by ozley, 04-05-2016 07:53 AM
    • Replies: 2
    • Views: 1,067
    04-05-2016, 09:32 PM Go to last post
  11. Nightmare start

    Started by d43d, 01-21-2016 05:21 AM
    5 Pages
    1 2 3 ... 5
    • Replies: 47
    • Views: 8,233
    04-01-2016, 02:42 PM Go to last post
  12. X-Axis off by a few percent / Circles not round

    Started by noa, 03-26-2016 07:04 PM
    • Replies: 9
    • Views: 2,626
    03-31-2016, 12:17 PM Go to last post
  13. New CTC printer came broken

    Started by dspdrew, 02-27-2016 02:19 PM
    7 Pages
    1 2 3 ... 7
    • Replies: 68
    • Views: 10,878
    03-23-2016, 04:46 AM Go to last post
  14. Filament refusing to feed.

    Started by dlps73, 03-01-2016 05:50 PM
    3 Pages
    1 2 3
    • Replies: 21
    • Views: 5,200
    03-19-2016, 09:37 AM Go to last post
  15. Shrinkage?

    Started by dlps73, 03-14-2016 04:35 PM
    • Replies: 4
    • Views: 871
    03-14-2016, 06:41 PM Go to last post
  16. Updating the board with a Atmega2560

    Started by TraxXavier, 03-06-2016 01:49 AM
    • Replies: 2
    • Views: 1,292
    03-07-2016, 11:52 AM Go to last post
  17. Extruder not reaching operating temp

    Started by err404, 02-19-2016 01:32 PM
    • Replies: 8
    • Views: 3,157
    02-20-2016, 11:56 AM Go to last post
  18. New CTC Owner

    Started by bigo93, 12-18-2015 08:40 PM
    6 Pages
    1 2 3 ... 6
    • Replies: 52
    • Views: 9,362
    02-15-2016, 06:09 PM Go to last post
  19. CTC printer issue

    Started by stormy17, 02-14-2016 12:01 PM
    • Replies: 3
    • Views: 1,011
    02-15-2016, 08:17 AM Go to last post

Page 3 of 6 FirstFirst 12345 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •