Activity Stream
-
Older Activity
-
Yesterday, 12:32 PMBikeracer2020 replied to a thread Catastrophic failure on Creality Ender-3 V3 KE in Tips, Tricks and Tech HelpThe filament monster is probably because the nozzle has a less than perfect seal to the hot end, causing the molten filament to leak. I don't know...1 replies | 221 view(s)
-
Yesterday, 12:01 PMKalkowski started a thread Catastrophic failure on Creality Ender-3 V3 KE in Tips, Tricks and Tech HelpHi, i am new to 3d printing, this is my second printer, bought brand new 2 weeks ago.i have been using the factory settings and regular PLA...1 replies | 221 view(s)
-
Yesterday, 07:41 AMIt sounds like moisture to me as well. I may have missed it but have you tired putting some cardboard or something around to create a simple...188 replies | 318398 view(s)
-
04-15-2024, 05:36 AMsamsonwilliams started a thread Creating a bronze-Like finish for outdoor 3D printed plaque in General 3D Printing DiscussionDoes anyone know how I could paint a 3D printed plaque so that it looks like its bronze? It will need to hold up outside with the desert sun beating...0 replies | 485 view(s)
-
04-14-2024, 08:58 PMI have printed for a few years on a Creality Ender-5 with few problems. I have some rather small parts that are doing fine with a 0.4mm Nozzle, but I...0 replies | 285 view(s)
-
04-14-2024, 05:15 PMIn my Slicer Software there is an option to randomize location of seam to virtually make it invisible.2 replies | 602 view(s)
-
04-14-2024, 12:34 PMWell it looks kind of dumb but it works. I have a 235X235 build sheet (for an Ender) stuck to a 235X235 PEI build plate (also for an Ender) I...5 replies | 3015 view(s)
-
04-14-2024, 11:26 AMI made the z change in the printer itself. It is a delta running smoothieware so it is very easy to make changes in the firmware. Then I fine...5 replies | 3015 view(s)
-
04-14-2024, 01:46 AMDid You adjust the 'Z' offset in the slicer or just the 'Z' height when setting the initial nozzle difference? I should have made that clearer in...5 replies | 3015 view(s)
-
04-13-2024, 02:50 PMI have been struggling with these plates for almost a year now. I have a cartesian and a delta printer. I print PETG and ABS on the cartesain and...5 replies | 3015 view(s)
-
04-12-2024, 11:54 AMOG56 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersThere is a lot of abuse currently being done with AI in different markets. Some of the sites I frequent have lately been flooded by AI...2 replies | 781 view(s)
-
04-12-2024, 11:03 AMThe line is called a 'Z' seam, it happens where one layer ends and the next one starts. There are settings in the slicer as to where you want it...2 replies | 602 view(s)
-
04-12-2024, 09:56 AMHow can I solve this and why does it happen? what's the type of error called? (see attached)I'm using a Anycubic Kobra 2 Max and I'm slicing using...2 replies | 602 view(s)
-
04-12-2024, 02:21 AMTwo suggestions...... Try Prusaslicer or Orca slicer. Or email.. may@qd3dprinter.com2 replies | 723 view(s)
-
04-12-2024, 02:13 AMBikeracer2020 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersI think all this AI generated stuff is rapidly leading to a place where it will be impossible to distinguish between fact and fiction. In your...2 replies | 781 view(s)
-
04-11-2024, 08:43 PMOG56 started a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersHopefully can generate fun discussion. In the last year or two, AI has delved into 3d modeling and height map generation. Though still in the...2 replies | 781 view(s)
-
04-11-2024, 02:19 PMI should mention that the Side bar with settings IS visible.2 replies | 723 view(s)
-
04-11-2024, 02:17 PMmy first printer, i have successfully printed the built in g-code samples from QIDI Slicer, and downloaded g-code calibration files from teachingtech...2 replies | 723 view(s)
-
04-11-2024, 06:08 AMBikeracer2020 replied to a thread WHY DOES MY PRINT LOOK LIKE THIS Please help! in General 3D Printing DiscussionTry just using your standard slicer profile for the filament.1 replies | 865 view(s)
-
04-11-2024, 05:58 AM3dIncredible started a thread 3D Incredible: Additive Manufacturing Company in Pune, India in Free Self Promotion3D Incredible, an additive manufacturing company in India, is transforming industries with their advanced 3D printing applications. Their tailored...0 replies | 560 view(s)
-
04-09-2024, 05:08 PMhaq started a thread WHY DOES MY PRINT LOOK LIKE THIS Please help! in General 3D Printing DiscussionHey thanks for stopin by im trying to print a rc plane and i keep getting this issue1 replies | 865 view(s)
-
04-09-2024, 05:43 AMHello everyone. I am optimizing my print s on the S5. As you can see, the quality of the slingshot is nearly perfect. but around the z-scar there...0 replies | 445 view(s)
-
04-08-2024, 07:25 PMcaarsonr started a thread Seeking Help with Monoprice Maker Select V2 After Y-axis Limit Switch Repair in Tips, Tricks and Tech HelpHello everyone, I'm currently grappling with a challenging issue on my Monoprice Maker Select V2 and would appreciate any advice or insights this...0 replies | 763 view(s)
-
04-08-2024, 12:32 PMSave your coins in a triceratops piggy bank!https://cults3d.com/en/3d-model/art/trike-piggy-bank0 replies | 702 view(s)
QIDI Slicer "Plater" is...
04-12-2024, 02:21 AM in QiDi 3D Printer Forum