Activity Stream
-
Older Activity
-
Today, 05:20 PMIndo Printing Jakarta replied to a thread Best 3D printer for me? Comment advice. in General 3D Printing DiscussionThank you so much for the information you shared, it was just what I was looking for. Today is a wonderful day, do you want to participate to visit...109 replies | 198120 view(s)
-
Today, 03:07 PMBikeracer2020 replied to a thread Adventurer 3 filling holes in design! in Tips, Tricks and Tech HelpLoaded your STL into Orca slicer and it appears you have two STL's one on top of the other.1 replies | 146 view(s)
-
Today, 11:53 AMhello, relatively new to 3d printing although i did some at university. I am currently trying to print a speaker grill for my car, however all the...1 replies | 146 view(s)
-
Today, 04:38 AMworld of warcraft or dota15 replies | 18675 view(s)
-
Today, 02:22 AMIt's done ! Another one : Barbarian Saber is now unlocked :)15 replies | 5505 view(s)
-
Today, 12:58 AMHello everyone, one more unlocked Stretch goal : Tomahawk Saber !! The next one is close ! 24 hours left !! Have a fun day ^^15 replies | 5505 view(s)
-
Today, 12:02 AMCongrats on the 1X. I have a P1P and have yet to open a glue stick. The build plate has been awesome all by itself and I have had zero printer...3 replies | 1111 view(s)
-
Yesterday, 03:11 PMThanks mate, greatly appreciated. I realised I was using too much glue, I decided to try no glue at all and got perfect bed adhesion and didn't face...3 replies | 1111 view(s)
-
Yesterday, 10:49 AMI just did a quick google for 3d printing bed adhesion issues and this one should answer all your questions ...3 replies | 1111 view(s)
-
Yesterday, 07:48 AMSo, for anyone also experiencing this issue i found the problem.It was the TMC2208 stepper drivers overheating. I noticed when opining the...1 replies | 739 view(s)
-
Yesterday, 03:18 AMHello again, another stretch goal just unlocked !! The Old West saber is now available ! Let's have a look at the next one : the Tomahawk Saber !...15 replies | 5505 view(s)
-
Yesterday, 02:07 AMHello everyone, we are close to the end of the campaign :) NOW YOU CAN GET MORE THAN 260 STL PARTS FOR ONLY 34 EUROS (37 DOLLARS) !!! 15...15 replies | 5505 view(s)
-
03-16-2024, 08:44 PMHi, I have lost the USB connection with the printer. I updated the firmware, and after it loaded, when I try to print through CURA it doesn't...0 replies | 726 view(s)
-
03-16-2024, 07:47 PMatmane.djalil09 started a thread How to change printing parameters for PA6 in 3D Systems SPRO 60 ? in 3D Printers (Hardware)Hello,I am a PhD student working on evaluating the mechanical and geometric quality of parts printed using Selective Laser Sintering,I have already...0 replies | 859 view(s)
-
03-16-2024, 06:56 PMfred_dot_u replied to a thread Help selecting a really good 3D printer for a middle school? in 3D Printers (Hardware)People might consider me to be a Prusa fanboy, but my experience is a few years old. The local public library purchased without advisories a Cube 3...1 replies | 1198 view(s)
-
03-16-2024, 08:47 AMRHg started a thread top surface / layer bad quality Bambu Lab P1S printer in Tips, Tricks and Tech Helphi, my top surfaces went from printing almost perfect like the green circle shows on the below photo to printing rough and scratched top surfaces...0 replies | 922 view(s)
-
03-16-2024, 12:13 AMHello Everyone and thanks for checking out my little start-up QT Bits. QT Bits is a technology company that aims to deliver innovative and unique...0 replies | 546 view(s)
-
03-15-2024, 06:08 PMPete Moss started a thread Help selecting a really good 3D printer for a middle school? in 3D Printers (Hardware)My grandkids are in a small private middle school. They do not have a 3D printer, but would like one. I would appreciate recommendations for a really...1 replies | 1198 view(s)
-
03-15-2024, 02:22 PMHello everyone, I am new to this forum and new to 3D printing. Recently bought a Bambulab X1 Carbon and have been playing around with it over the...3 replies | 1111 view(s)
-
03-15-2024, 10:19 AMHello again ! Another Stretch goal !! Huge lot of STL parts for many many sabers :) Let's go to the next one : the Old West saber :) Have...15 replies | 5505 view(s)
Newbie Question
Today, 12:02 AM in Tips, Tricks and Tech Help